Bitmain Antminer S19 XP+ Hyd (266Th)은(는) Bitmain의 SHA-256 알고리즘용 ASIC 채굴기로, 5,054 W에서 266 TH/s의 성능을 냅니다. 2025년 1월에 출시되었습니다. 효율 19.0 J/TH는 저희가 추적하는 SHA-256 채굴기 중앙값(20.4 J/TH)과 비슷합니다. $0.036/kWh 기준 일일 수익으로 299대의 SHA-256 채굴기 중 94위이며, BTC 채굴로 하루 약 $5.31를 법니다. AsicProfit 최저가는 $2,961입니다. 현재 수치로는 약 558일 만에 본전을 찾습니다. 수냉(hydro) 방식이라 팬 대신 냉각 루프와 드라이 쿨러가 필요합니다.
질문과 답변 6
이 채굴기에 대해 질문하세요. 인증된 계정이 질문하고 답하며, 판매자는 매장 이름으로 답합니다. 모든 글은 확인 후 게시됩니다.
Oleh B. · 2026년 10월 21일 · 다른 버전에 대해
how often do I have to check the coolant on a hydro miner
AsicProfit SupportAsicProfit · 2026년 10월 22일
Bitmain's guide puts pH at the centre of routine checks and says coolant below pH 7 should not be used. Test pH roughly every six months, track freezing point and conductivity, and do a full coolant check at least once a year. When draining for repair, empty the miner completely.
Sophie M. · 2026년 10월 20일 · 다른 버전에 대해
Is there warranty on a used S19 XP+ Hyd?
AsicProfit SupportAsicProfit · 2026년 10월 21일
Bitmain's standard warranty for new S19 and later miners is 365 days from the official shipment date, subject to the sales contract, and is tied to the serial number. A used unit keeps whatever is left of that period. Check the serial on Bitmain's warranty check page before buying. Out of warranty units can still be repaired for a fee.
Milan P. · 2026년 10월 16일 · 다른 버전에 대해
do I need a full cooling container or can I run one at home with a dry cooler
AsicProfit SupportAsicProfit · 2026년 10월 17일
Bitmain designs it to run with its own hydro cooling infrastructure, but what the miner needs is the flow, pressure, temperature and fluid quality in its spec. A home loop with a pump, dry cooler and plate heat exchanger can meet that if sized for over 5 kW of heat per unit, plus three phase power. Most owners use a hosting site.
Tomas N. · 2026년 10월 13일 · 다른 버전에 대해
What coolant, flow and pressure does the XP+ Hyd need?
AsicProfit SupportAsicProfit · 2026년 10월 14일
Bitmain lists 8 to 10 litres per minute per unit, pressure up to 3.5 bar, inlet coolant 20 to 50°C, and OD10 pipe connectors. Approved fluids are antifreeze (pH 7.0 to 9.0), pure water (6.5 to 7.5) or deionized water (8.5 to 9.5). Use a glycol mix rated for the lowest temperature on site, since frozen and cracked heat exchangers are not covered.
Katarina H. · 2026년 10월 11일 · 다른 버전에 대해
Can I plug an S19 XP+ Hyd into normal single phase power?
AsicProfit SupportAsicProfit · 2026년 10월 11일
No. Bitmain specifies three phase 380 to 415 V, 50 or 60 Hz, up to 12 A per phase, through an APW11 power supply with a waterproof connector. The power cord is not included. Bitmain also requires an earthed supply, a surge protection device and a disconnect that cuts all three phases at once. Plan the electrical work with a qualified electrician.
Daniel F. · 2026년 9월 13일 · 다른 버전에 대해
What is the actual difference between the 279T and 293T versions?
AsicProfit SupportAsicProfit · 2026년 9월 14일
They are the same machine in different bins. Bitmain lists 279 TH/s at about 5,301 W and 293 TH/s at about 5,567 W, both around 19 J/TH at 35°C coolant inlet. The 293T makes more hashrate and needs more power and cooling capacity per unit. Compare both in the calculator at your power price.