OneMiners★ Zvýraznění✓ Ověřený prodejceProdloužená zárukaPlatba na splátkySkladem, rychlé dodáníAntminer S19k Pro - 110 TH/sHosting u nich od $0.0364/kWh, $67 měsíčněOdesílá se z: United States · ověřeno před 23 h
Kalkulačka z našeho bezplatného widgetu: podle ní se počítá každá návratnost na této stránce.
Příjem za den
$4.02
Elektřina za den
−$2.21
Hosting za den
—
Zisk za den
$1.81
Návratnost při $297
—
Zisk a návratnost jsou odhady z dnešních cen kryptoměn a obtížnosti sítě, před poplatky poolu, hostingem a daněmi. Mění se každý den. Nejde o finanční poradenství.
Žebříčky počítají s hlavní mincí algoritmu (BTC pro SHA-256, LTC + DOGE pro Scrypt): malé vedlejší chainy dnes mohou platit víc za hash, ale velký hashrate nepojmou.
Bitmain Antminer S19k Pro (110Th) je ASIC těžební stroj od Bitmain pro algoritmus SHA-256 s výkonem 110 TH/s při 2,530 W. Uveden na trh: duben 2023. Se spotřebou 23.0 J/TH spotřebuje na hash o 15 % více energie než medián strojů SHA-256, které sledujeme (20.0 J/TH). Při $0.036/kWh je na 157. místě z 299 strojů SHA-256 podle denního zisku a vydělá zhruba $1.81 denně těžbou BTC. Nejlepší cena na AsicProfit je $297. Při dnešních hodnotách se zaplatí zhruba za 164 dní. S 75 dB patří do těžební farmy nebo hostingu.
Dotazy a odpovědi 6
Zeptejte se na tento miner. Ověřené účty se ptají a odpovídají, prodejci odpovídají za svůj obchod a každý příspěvek před zveřejněním kontrolujeme.
Ryan M. · 26. 10. 2026 · k jiné verzi
Getting a fan error. How do I find which of the four fans has failed?
AsicProfit SupportAsicProfit · 27. 10. 2026
The fan numbers in the log do not always match the labels on the control board, which confuses many owners. The quickest way is to check the fan speeds in the status page, then unplug fans one at a time and watch which reading changes. Replace with a fan that has the same connector type. Owners running several units keep spare fans on hand, since fans fail far more often than boards.
Stefan I. · 22. 10. 2026 · k jiné verzi
how noisy is the s19k pro, could it go in a spare bedroom with a sound box
AsicProfit SupportAsicProfit · 22. 10. 2026
It is listed at about 75 dB with four fans, which is too loud for a bedroom. A sound-dampening box helps, but it must not starve the miner of air. One owner's abnormal hashrate and restart problems went away after taking the miner out of its noise box and reseating the power cables. A garage or ventilated outbuilding, with ducting for the hot exhaust, is the usual home setup.
Mikkel J. · 17. 10. 2026 · k jiné verzi
Is a 23 J/TH machine like the S19k Pro still worth buying now?
AsicProfit SupportAsicProfit · 19. 10. 2026
It can be, but only with cheap power. At around 23 J/TH it spends more electricity per terahash than current-generation machines, so rising network difficulty or a lower Bitcoin price squeezes its margin first. Its appeal is a lower purchase price and modest 2.76 kW draw. Put your real electricity price into the calculator on this page and compare it with a newer model before deciding.
Omar H. · 1. 10. 2026 · k jiné verzi
Can I run an S19k Pro on 110V/120V household power?
AsicProfit SupportAsicProfit · 1. 10. 2026
No. It is built for 220V-class input and draws about 2,760 W, and an experienced forum helper warned an owner that it will not run normally on 110V. On 230V it pulls about 12A, so give it a dedicated circuit rather than sharing one with other loads, and plug it in directly instead of through a light extension lead. Unstable power is a common cause of restarts and hashrate drops.
Janez N. · 16. 9. 2026 · k jiné verzi
Updated firmware and now it says board name doesn't match and won't hash. Can I fix it?
AsicProfit SupportAsicProfit · 17. 9. 2026
That error means the firmware does not match your hashboard revision. Newer S19k Pro batches can need a specific firmware, and flashing third-party or older images can leave the unit unable to start. If the unit is still under warranty, ask Bitmain support for the correct firmware for your serial number first. The SD card recovery image from Bitmain's download page is the next step. Avoid flashing a new, working machine just to try other firmware.
Ivan G. · 16. 9. 2026 · k jiné verzi
one hashboard only finds 76 of 77 chips after a restart, what should i check?
AsicProfit SupportAsicProfit · 17. 9. 2026
Start simple: power off, reseat and clean the data cable between control board and hashboard, then test each board on its own, since one faulty board can upset readings for the others. Try the stock firmware and a factory reset. If the board still drops a chip, a missing chip in a series chain usually needs a repair shop or a warranty claim. Some third-party firmware will run a board with a weak chip, but it cannot bypass a dead one.
Pro položení dotazu se přihlaste ověřeným účtem. Přihlásit se